Perfectly Twisted Handmade Wire Wrapped Beaded and Gemstone Jewelry: copper

Showing posts with label copper. Show all posts

How to Create Balls on Copper Wire Ends Using a Butane Micro Torch aka How to Make Copper Headpins Part 1

I love the look of balled ends on wire and I've seen it in many places along the web, in silver wire. I work mostly in copper, which is a harder metal, but I wanted to create this same effect... so a couple of weeks ago, I went to the local craft store and purchased a butane micro torch. Copper melts at 1981 degree Fahrenheit, so if you're going to give this a try, make sure the torch you purchase will reach or exceed this temperature.

The exact torch I have can be purchased at Michael's for about $40 ... if you already have this one, it will work for sure.

http://www.michaels.com/Butane-Torch/bd1328,default,pd.html

You can purchase lighter butane almost anywhere... I get mine at the Walgreens. You can also find it at Home Depot hardware stores.

My first try was a total misery and I wasn't able to get any gauge wire to ball up... including even a 20 gauge wire. After some time and reading, I finally figured out the 'trick' to getting those lovely balls... and I've managed to ball up wire as thick as 12 gauge using this butane micro torch.

Here's how...

Before you begin

1. Make sure you are working in a well ventilated area.

2. Use either a fire stone and/or a pan of water and work on a surface area that is not flammable.

3. Use pliers that are safe to handle and long enough to keep your fingers away from the flame.

4. Make sure your clothing and hair are pulled back and secure.

5. Make sure your butane micro torch is completely full for best results.

6. Use safety glasses if possible.

Grasp your wire length with the pliers, either in the center of the wire, or at the end opposite the one you intend to set the flame on.

The TRICK to this, is to get the tip of the wire and the tip of the flame, pointed head on, at each other. If the flame and the wire are perpendicular when you start, the wire will get red hot, but the end will never melt and ball up.

You will see the tip of the wire go red hot and the tip of the flame will become green... this is when the wire will begin to melt. There may be small sparks at this point, so don't be alarmed and don't put your face too close to the heat.

Once the wire end becomes molten, start to rotate the wire so that the balled end is pointed 'down', while you continue to hold the flame sideways and on the balled end. At this point, the balled end and the flame ARE perpendicular. This will create a nice rounded look to the molten ball.

Remove the flame from the wire while it's red hot and dip the whole wire, not just the end, into the pan of water to cool it down.

Keep in mind that your plier heads will be super hot also... so cool them down in the water too!

==============================

Part 2, Pictures! on how to do this...
http://perfectlytwistedjewelry.blogspot.com/2013/04/using-butane-micro-torch-to-create.html

oSo! New, the latest in my etsy store, Perfectly Twisted Jewelry

The link to the store is here.... please go and shop your hearts out! ;)

The How To... A Picture Tutorial on Wire Weaved Jewelry... Create a Wire Wrapped Pendant ...Part 2

This finished pendant can be purchased in my etsy store...
Click here to go there! I hope you've enjoyed the picture tutorial, I know. there are no words ;) x

The How To... A Picture Tutorial on Wire Weaved Jewelry... Create a Wire Wrapped Pendant ...Part 1

I've had several emails asking 'how' do I create some of these pendants... so I thought I'd share these images with you and give you a peak into the studio. I hope you enjoy the 'picture tutorial' and find inspiration for your wire craft! Click each image to enlarge and get a closer look at the wire.

1 inch by 1 inch glass focal bead
Five, 20 gauge, bare copper wires, approximately 1 foot each
Lots of 28 gauge, bare copper weaving wire ;)
Patience... and good lighting.
CoolTools Patina Gel

1.

To be continued....

NEW! Copper Wire Pendants and Necklaces

I've added a few things to my etsy shop, I hope you'll give a look... ;) Have a wonderful and creative day!

This Chalcedony butterfly pendant was a pattern I learned from the wonderful artist, Iza Malczyk. Her etsy store is linked here and I encourage anyone to try her tutorials. She has wonderful designs as well as clearly written instructions and great images throughout the tutorial. I'm a huge fan and am grateful such a wonderful artist is willing to share her talents with us. The pattern is wonderful to work with and can be modified in many ways... I do hope you give it a try.

New! Wired to Love You, Copper and Bronze Wire Pendants

So it's finally done! I'm really happy with how the patina turned out along with the whole piece. I also put a patina to the copper chain as well as the clasp. I decided that a machine made clasp wasn't going to 'do it' for this beautiful pendant, so I designed my own. Wired into the heart are Garnet and Spinel briolettes and rondelles as well as accent copper beads. I loved making this piece and it's perfectly on time for the upcoming Valentine's day. Enjoy the eye candy, I just posted these pieces into my etsy store!
http://www.etsy.com/shop/PerfectlyTwisted

Click each image to enlarge and feel free to email me at IzzyzGumbo@gmail.com for questions.

Gems Medley
Copper wire, oxidized, buffed and sealed to keep the gorgeous antique finish. Iolite, amethyst, peridot, spinel gemstones and copper beads.